Skip to main content
Engineering LibreTexts

8.5: Heat Sink Usage

  • Page ID
    3597
  • \( \newcommand{\vecs}[1]{\overset { \scriptstyle \rightharpoonup} {\mathbf{#1}} } \) \( \newcommand{\vecd}[1]{\overset{-\!-\!\rightharpoonup}{\vphantom{a}\smash {#1}}} \)\(\newcommand{\id}{\mathrm{id}}\) \( \newcommand{\Span}{\mathrm{span}}\) \( \newcommand{\kernel}{\mathrm{null}\,}\) \( \newcommand{\range}{\mathrm{range}\,}\) \( \newcommand{\RealPart}{\mathrm{Re}}\) \( \newcommand{\ImaginaryPart}{\mathrm{Im}}\) \( \newcommand{\Argument}{\mathrm{Arg}}\) \( \newcommand{\norm}[1]{\| #1 \|}\) \( \newcommand{\inner}[2]{\langle #1, #2 \rangle}\) \( \newcommand{\Span}{\mathrm{span}}\) \(\newcommand{\id}{\mathrm{id}}\) \( \newcommand{\Span}{\mathrm{span}}\) \( \newcommand{\kernel}{\mathrm{null}\,}\) \( \newcommand{\range}{\mathrm{range}\,}\) \( \newcommand{\RealPart}{\mathrm{Re}}\) \( \newcommand{\ImaginaryPart}{\mathrm{Im}}\) \( \newcommand{\Argument}{\mathrm{Arg}}\) \( \newcommand{\norm}[1]{\| #1 \|}\) \( \newcommand{\inner}[2]{\langle #1, #2 \rangle}\) \( \newcommand{\Span}{\mathrm{span}}\)\(\newcommand{\AA}{\unicode[.8,0]{x212B}}\)

    Whenever appreciable amounts of power are dissipated by semiconductor devices, some form of cooling element needs to be considered. Power supply regulation circuits are no exception. The pass transistors used in both linear and switching regulators can be forced to dissipate large amounts of power. The result of this is the production of heat. Generally, the life-span of semiconductors drops as the operation temperature rises. Most silicon-based devices exhibit maximum allowable junction temperatures in the 150\(^{\circ}\)C range. Although power transistors utilize heavier metal cases, they are generally not suitable for high dissipation applications by themselves.

    In order to increase the thermal efficiency of the device, an external heat sink is used. Heat sinks are normally made of aluminum and appear as a series of fins. The fins produce a large surface, which enhances the process of heat convection. In other words, the heat sink can transfer heat to the surrounding atmosphere faster than the power transistor can. By bolting the transistor to the heat sink, the device will be able to dissipate more power at a given operating temperature. Some typical heat sinks are shown in Figure \(\PageIndex{1}\).

    8.5.1.png

    Figure \(\PageIndex{1}\): Typical heatsinks. Reprinted courtesy of Thermalloy, Inc.

    8.5.1: Physical Requirements

    Heat sinks are designed to work with specific device-case styles. The most common case styles for regulators are the TO-220 “power tab”, and the TO-3 “can”. Heat sinks are available for these specific styles, including the requisite mounting hardware and insulation spacers. Some of the lower power regulators utilize TO-5 “mini can” or DIP-type cases. Heat sinks are available for these package types, too, but are not quite as common.

    There are a couple of general rules that should be followed when using heat sinks:

    • Always use some form of heat sink grease or thermally conductive pad between the heat sink and the device. This will increase the thermal transfer between the two parts. Note that excessive quantities of heat sink grease will actually decrease} performance.
    • Mount fins in the vertical plane for optimum natural convective cooling.
    • Do not overcrowd or obstruct devices that use heat sinks.
    • Do not block air flow around heat sinks - particularly directly above and below items that rely on natural convection.
    • If thermal demands are particularly high, consider using forced convection (e.g., fans).

    8.5.2: Thermal Resistance

    In order to specify a particular heat sink for a given application, a more technical explanation is in order. What we are going to do is create a thermal circuit equivalent. In this model, the concept of thermal resistance is used. Thermal resistance denotes how easy it is to transfer heat energy from one mechanical part to another. The symbol for thermal resistance is \(\theta \), and the units are Centigrade degrees per watt. In this model, temperature is analogous to voltage, and thermal power dissipation is analogous to current. A useful Equation is,

    \[ P_D = \frac{\Delta T}{\theta _{total}} \label{8.4} \]

    Where \(P_D\) is the power dissipated by the semiconductor device in watts, \(\Delta T\) is the temperature differential, and \(\theta _{total}\) is the sum of the thermal resistances. Basically, this is a thermal version of Ohm's Law.

    In order to construct our model, let's take a closer look at the power-device/heat-sink combination. This is shown in Figure \(\PageIndex{2}\). \(T_j\) is the semiconductor junction temperature. This heat energy source heats the device case to \(T_c\). The thermal resistance between the two entities is \(\theta _{jc}\). The case, in turn, heats the heat sink via the interconnection. This thermal resistance is \(\theta _{cs}\), and the resulting temperature is \(T_s\).

    Finally, the heat sink passes the thermal energy to the surrounding air, which is sitting at \(T_a\). The thermal resistance of the heat sink is \(\theta _{sa}\). The equivalent thermal model is shown in Figure \(\PageIndex{3}\). (Although this does not have perfect correspondence with normal circuit analysis, it does illustrate the main points.)

    8.5.2.png

    Figure \(\PageIndex{2}\): Device and heatsink.

    8.5.3.png

    Figure \(\PageIndex{3}\): Equivalent thermal model of Figure \(\PageIndex{2}\).

    In this model, ground represents a temperature of absolute zero. The circuit is sitting at an ambient temperature \(T_a\), thus a voltage source of \(T_a\) is connected to ground and the heat sink. The three thermal resistances are in series and are driven by a current source that is set by the present power dissipation of the device. Note that if the power dissipation is high, the resulting “voltage drops” across the thermal resistances are high. Voltage is analogous to temperature in this model, so this indicates that a high temperature is created. Because there is a maximum limit to \(T_j\), higher power dissipations require lower thermal resistances. As \(\theta _{jc}\) is set by the device manufacturer, you have no control over that element. However, \(\theta _{cs}\) is a function of the case style and the insulation material used, so you do have some control (but not a lot) over that. On the other hand, as the person who specifies the heat sink, you have a great deal of control over \(\theta _{sa}\). Values for \(\theta _{sa}\) are given by heat sink manufacturers. A useful variation of Equation \ref{8.4} is

    \[ P_D = \frac{T_j−T_a}{\theta _{jc} + \theta _{cs} + \theta _{sa}} \label{8.5} \]

    Normally, power dissipation, junction and ambient temperatures, \(\theta _{jc}\) and \(\theta _{cs}\) are known. The idea is to determine an appropriate heat sink. Both \(T_j\) and \(\theta _{jc}\) are given by the semiconductor device manufacturer. The ambient temperature, \(T_a\), may be determined experimentally. Due to localized warming, it tends to be higher than the actual “room temperature”. Standard graphs, such as those found in Figure \(\PageIndex{4}\), may be used to determine \(\theta _c\).

    Example \(\PageIndex{1}\)

    Determine the appropriate heat sink rating for a power device rated as follows: \(T_{j(max)}\) = 150\(^{\circ}\)C, TO-220 case style, \(\theta _{jc}\) = 3.0 C\(^{\circ}\)/W. The device will be dissipating a maximum of 6 W in an ambient temperature of 40\(^{\circ}\)C. Assume that the heat sink will be mounted with heat sink grease and a 0.002 mica insulator.

    First, find \(\theta _{cs}\) from the TO-220 graph. Curve 3 is used. The approximate (conservative) value is 1.6 C\(^{\circ}\)/W.

    \[ P_D = \frac{T_j − T_a}{\theta _{jc} + \theta _{cs} + \theta _{sa}} \nonumber \]

    \[ \theta _{sa} = \frac{T_j − T_a}{P_D} − \theta _{jc} − \theta _{cs} \nonumber \]

    \[ \theta _{sa} = \frac{150^{\circ}C−40^{\circ}C}{6W} − 3.0C^{\circ}/W−1.6C^{\circ}/W \nonumber \]

    \[ \theta _{sa} = 13.73C^{\circ}/W \nonumber \]

    This is the maximum acceptable value for the heat sink's thermal resistance. Note that the use of heat sink grease gives us an extra 2 C\(^{\circ}\)/W or so. Also, note the generally lower values of \(\theta _{sa}\) for the TO-3 case relative to the TO-220. This is one reason why TO-3 cases are used for higher power devices. This case also makes it easier for the manufacturer to reduce \(\theta _{jc}\).

    8.5.4.png

    Figure \(\PageIndex{4}\): \(\theta_{CS}\) for TO-3 and TO-220. Reprinted courtesy of Thermalloy, Inc.


    This page titled 8.5: Heat Sink Usage is shared under a CC BY-NC-SA 4.0 license and was authored, remixed, and/or curated by James M. Fiore via source content that was edited to the style and standards of the LibreTexts platform; a detailed edit history is available upon request.