Skip to main content
Engineering LibreTexts

12.9: Combination of the Oblique Shock and Isentropic Expansion

  • Page ID
    862
    \( \newcommand{\vecs}[1]{\overset { \scriptstyle \rightharpoonup} {\mathbf{#1}} } \) \( \newcommand{\vecd}[1]{\overset{-\!-\!\rightharpoonup}{\vphantom{a}\smash {#1}}} \)\(\newcommand{\id}{\mathrm{id}}\) \( \newcommand{\Span}{\mathrm{span}}\) \( \newcommand{\kernel}{\mathrm{null}\,}\) \( \newcommand{\range}{\mathrm{range}\,}\) \( \newcommand{\RealPart}{\mathrm{Re}}\) \( \newcommand{\ImaginaryPart}{\mathrm{Im}}\) \( \newcommand{\Argument}{\mathrm{Arg}}\) \( \newcommand{\norm}[1]{\| #1 \|}\) \( \newcommand{\inner}[2]{\langle #1, #2 \rangle}\) \( \newcommand{\Span}{\mathrm{span}}\) \(\newcommand{\id}{\mathrm{id}}\) \( \newcommand{\Span}{\mathrm{span}}\) \( \newcommand{\kernel}{\mathrm{null}\,}\) \( \newcommand{\range}{\mathrm{range}\,}\) \( \newcommand{\RealPart}{\mathrm{Re}}\) \( \newcommand{\ImaginaryPart}{\mathrm{Im}}\) \( \newcommand{\Argument}{\mathrm{Arg}}\) \( \newcommand{\norm}[1]{\| #1 \|}\) \( \newcommand{\inner}[2]{\langle #1, #2 \rangle}\) \( \newcommand{\Span}{\mathrm{span}}\)\(\newcommand{\AA}{\unicode[.8,0]{x212B}}\)

    Example 12.18

    Consider two–dimensional flat thin plate at an angle of attack of \(4^\circ\) and a Mach number of 3.3. Assume that the specific heat ratio at stage is \(k=1.3\), calculate the drag coefficient and lift coefficient.

    Solution 12.18

    For \(M=3.3\), the following table can be obtained:

    Prandtl — Meyer Input: \(M\) k = 1.4
    \(M\) \(\nu\) \(\dfrac{P}{P_0}\) \(\dfrac{T}{T_0}\) \(\dfrac{\rho}{\rho_0}\) \(\mu\)
    3.300 62.3113 0.01506 0.37972 0.03965 73.1416

    With the angle of attack the region 3 will be at \(\nu \sim 62.31+4\) for which the following table can be obtained (Potto-GDC)

    Prandtl — Meyer Input: \(M\) k = 1.4
    \(M\) \(\nu\) \(\dfrac{P}{P_0}\) \(\dfrac{T}{T_0}\) \(\dfrac{\rho}{\rho_0}\) \(\mu\)
    3.4996 66.3100 0.01090 0.35248 0.03093 74.0528

    On the other side, the oblique shock (assuming weak shock) results in

    Oblique Shock Input: \(M_x\) k = 1.4
    \(M_x\) \({{M_y}_s}\) \({{M_y}_w}\) \(\theta_{s}\) \(\theta_{w}\) \(\delta\) \(\dfrac{{P_0}_y}{{P_0}_x}\)
    3.300 0.43534 3.1115 88.9313 20.3467 4.0000 0.99676

    and the additional information, by clicking on the minimal button, provides

    Oblique Shock Input: \(M_x\) k = 1.4
    \(M_x\) \({{M_y}_w}\) \(\theta_{w}\) \(\delta\) \(\dfrac{{P}_y}{{P}_x}\) \(\dfrac{{T}_y}{{T}_x}\) \(\dfrac{{P_0}_y}{{P_0}_x}\)
    3.300 3.1115 20.3467 4.0000 1.1157 1.1066 0.99676

    The pressure ratio at point 3 is
    \begin{align*}
    \dfrac{P_3 }{ P_1} = \dfrac{P_3 }{ P_{03} } \, \dfrac{P_{03} }{ P_{01}} \, \dfrac{P_{01} }{ P_{1}}
    = 0.0109 \times 1 \times \dfrac{1 }{ 0.01506} \sim 0.7238
    \end{align*}
    The pressure ratio at point 4 is
    \begin{align*}
    {P_3 \over P_1} = 1.1157
    \end{align*}
    \begin{align*}
    d_L = {2 \over k P_1 {M_1}^2 }(P_4 - P_3) \cos \alpha =
    {2 \over k {M_1}^2 } \left( {P_4 \over P_1} - {P_3 \over P_1} \right) \,\cos \alpha
    \end{align*}
    \begin{align*}
    d_L = { 2 \over 1.3 3.3^2 } \left( 1.1157 - 0.7238 \right) \cos 4^\circ \sim .054
    \end{align*}
    \begin{multline*}
    d_d = \dfrac{2 }{ k\, {M_1}^2 } \left( \dfrac{P_4 }{ P_1} - \dfrac{P_3 }{ P_1} \right) \sin \alpha =
    \dfrac{ 2 }{ 1.3\, 3.3^2 } \left( 1.1157 - 0.7238 \right) \sin 4^\circ
    \sim .0039
    \end{multline*}
    This shows that on the expense of a small drag, a large lift can be obtained. Discussion on the optimum design is left for the next versions.

    Fig. 12.31 Schematic of the nozzle and Prandtl–Meyer expansion.

    Example 12.19

    To understand the flow after a nozzle consider a flow in a nozzle shown in Figure 12.31. The flow is choked and additionally the flow pressure reaches the nozzle exit above the surrounding pressure. Assume that there is an isentropic expansion (Prandtl–Meyer expansion) after the nozzle with slip lines in which there is a theoretical angle of expansion to match the surroundings pressure with the exit. The ratio of exit area to throat area ratio is 1.4. The stagnation pressure is 1000 [kPa]. The surroundings pressure is 100[kPa]. Assume that the specific heat, \(k=1.3\). Estimate the Mach number after the expansion.

    Solution 12.19

    The Mach number a the nozzle exit can be calculated using Potto-GDC which provides

    Isentropic Flow Input: \(\dfrac{A}{A^{\star}}\) k = 1.3
    \(M\) \(\dfrac{T}{T_0}\) \(\dfrac{\rho}{\rho_0}\) \(\dfrac{A}{A^{\star}}\) \(\dfrac{P}{P_0}\) \(\dfrac{{A\,P}_y}{{A^{\star}\,P_0}_x}\) \(\dfrac{F}{F_0}\)
    1.7285 0.69052 0.29102 1.4000 0.20096 0.28134 0.59745

    Thus, the exit Mach number is 1.7285 and the pressure at the exit is
    \begin{align*}
    P_{exit} = P_0 \dfrac{P_{\text{exit}}}{P_0} = 1000 \times 0.20096 = 200.96 [kPa]
    \end{align*}
    This pressure is higher than the surroundings pressure and an expansion must occur. This pressure ratio is associated with a expansion angle that Potto-GDC provide as

    Oblique Shock Input: \(M_x\) k = 1.3
    \(M_x\) \({{M_y}_w}\) \(\theta_{w}\) \(\delta\) \(\dfrac{{P}_y}{{P}_x}\) \(\dfrac{{T}_y}{{T}_x}\) \(\dfrac{{P_0}_y}{{P_0}_x}\)
    3.300 3.1115 20.3467 4.0000 1.1157 1.1066 0.99676

    The final pressure ratio ultimately has to be
    \begin{align*}
    \dfrac{ P_{\text{surroundings}}} {P_{0}} =
    \dfrac{100}{1000} = .1
    \end{align*}
    Hence the information for this pressure ratio can be provided by Potto-GDC as

    Oblique Shock Input: \(M_x\) k = 1.3
    \(M_x\) \({{M_y}_w}\) \(\theta_{w}\) \(\delta\) \(\dfrac{{P}_y}{{P}_x}\) \(\dfrac{{T}_y}{{T}_x}\) \(\dfrac{{P_0}_y}{{P_0}_x}\)
    3.300 3.1115 20.3467 4.0000 1.1157 1.1066 0.99676

    The change of the angle is
    \begin{align*}
    \Delta \text{angle} = 30.6147 - 20.0641 = 10.5506
    \end{align*}
    Thus the angle, $\beta$ is
    \begin{align*}
    \beta = 90 - 10.5506 \sim 79.45
    \end{align*}
    The pressure at this point is as the surroundings. However, the stagnation pressure is the same as originally was enter the nozzle! This stagnation pressure has to go through serious of oblique shocks and Prandtl-Meyer expansion to match the surroundings stagnation pressure.

    Contributors and Attributions

    • Dr. Genick Bar-Meir. Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.2 or later or Potto license.


    This page titled 12.9: Combination of the Oblique Shock and Isentropic Expansion is shared under a GNU Free Documentation License 1.3 license and was authored, remixed, and/or curated by via source content that was edited to the style and standards of the LibreTexts platform; a detailed edit history is available upon request.


    This page titled 12.9: Combination of the Oblique Shock and Isentropic Expansion is shared under a GNU Free Documentation License 1.3 license and was authored, remixed, and/or curated by Genick Bar-Meir via source content that was edited to the style and standards of the LibreTexts platform; a detailed edit history is available upon request.

    • Was this article helpful?