# 8.4: Momentum Conservation

- Page ID
- 746

The relationship among the shear stress various components have to be established. The stress is a relationship between the force and area it is acting on or force divided by the area (division of vector by a vector). This division creates a tensor which the physical meaning will be explained here (the mathematical explanation can be found in the mathematical appendix of the book). The area has a direction or orientation which control the results of this division. So it can be written that

\[

\label{dif:eq:stressD}

\boldsymbol{\tau} = f (\pmb{F},\pmb{A}) \tag{1}

\]

It was shown that in a static case (or in better words, when the shear stresses are absent) it was written

\[

\label{dif:eq:noStress}

\boldsymbol{\tau} = -P\,\widehat{n} \tag{2}

\]

It also was shown that the pressure has to be continuous. However, these stresses that act on every point and have three components on every surface and depend on the surface orientation. A common approach is to collect the stress in a "standard'' orientation and then if needed the stresses can be reorientated to a new direction. The transformation is available because the "standard'' surface can be transformed using trigonometrical functions. In Cartesian coordinates on surface in the \(x\) direction the stresses are

\[

\label{dif:eq:tauX}

\boldsymbol{\tau}^{(x)} = \qquad \tau_{xx} \qquad \tau_{xy}\qquad \tau_{xz} \tag{3}

\]

where \(\tau_{xx}\) is the stress acting on surface \(x\) in the \(x\) direction, and \(\tau_{xy}\) is the stress acting on surface \(x\) in the \(y\) direction, similarly for \(\tau_{xz}\). The notation \(\boldsymbol{\tau}^{(x_i)}\) is used to denote the stresses on \(x_i\) surface. It can be noticed that no mathematical symbols are written between the components. The reason for this omission is that there is no physical meaning for it. Similar "vectors'' exist for the \(y\) and \(z\) coordinates which can be written in a matrix form

\[

\label{dif:eq:tauComplit}

\boldsymbol{\tau} =

\left(

\begin{array}{rcl}

\tau_{xx} & \tau_{xy} & \tau_{xz} \\

\tau_{yx} & \tau_{yy} & \tau_{yz} \\

\tau_{zx} & \tau_{zy} & \tau_{zz}

\end{array}

\right) \tag{4}

\]

The same can be done for \(y\) and \(z\) directions. The areas are related to each other through angles. These relationships provide the transformation for the different orientations which depends only angles of the orientations. This matrix is referred to as stress tensor and as it can be observed has nine terms.

### The Symmetry of the Stress Tensor

A small liquid cubical has three possible rotation axes. Here only one will be discussed the same conclusions can be drown on the other direction. The cubical rotation can involve two parts: one distortion and one rotation . A finite angular distortion of infinitesimal cube requires an infinite shear which required for infinite moment. Hence, the rotation of the infinitesimal fluid cube can be viewed as it is done almost as a solid body rotation. Balance of momentum around the \(z\) direction shown in Figure 8.6 is

\[

\label{dif:eq:cubeM}

M_z = I_{zz} \dfrac{d\theta}{dt} \tag{9}

\]

Where \(M_z\) is the cubic moment around the cubic center and \(I_{zz}\) is the moment of inertia around that center. The momentum can be asserted by the shear stresses which act on it. The shear stress at point \(x\) is \(\tau_{xy}\). However, the shear stress at point \(x+dx\) is

\[

\label{dif:eq:tauxydx}

\left. \tau_{xy} \right|_{x+dx} = \tau_{xy} + \dfrac{d\tau_{xy}}{dx}dx \tag{10}

\]

The moment that results from this shear force (clockwise positive) is

\[

\label{dif:eq:tauxxM}

\int_y^{y+dy} \tau_{xx}(\eta)\,\left(\eta - \dfrac{dy}{2\dfrac{}{}} \right) d\eta \tag{12}

\]

Substituting (11) into (12) results

\[

\label{dif:eq:tauOneSideM}

\int_y^{y+dy} \left( \left. \tau_{xx} \right|_y + \left. \dfrac{d\tau_{xx}}{dy\dfrac{}{}} \right|_y \eta\right)

\,\left(\eta - \dfrac{dy}{2\dfrac{}{}} \right) d\eta \tag{13}

\]

The integral of (13) isn't zero (non symmetrical function around the center of integration). The reason that this term is neglected because on the other face of the cubic contributes an identical term but in the opposing direction (see Figure 8.6)

End Advance Material

The net torque in the z-direction around the particle's center would then be

\[

\label{dif:eq:tauTourque}

\begin{array}{rcl}

\left( \tau_{yx} \right) \dfrac{dx\,dy\,dz}{2} - &

\left( \tau_{yx} + \dfrac{\partial \tau_{xy}}{\partial x\dfrac{}{}} \right) \dfrac{dx\,dy\,dz}{2} +

\left( \tau_{xy} \right) \dfrac{dx\,dy\,dz}{2} -

& \\ &

\left( \tau_{xy} + \dfrac{\partial \tau_{xy}}{\partial x\dfrac{}{}} \right) \dfrac{dx\,dy\,dz}{2}

= \overbrace{\rho\,dx\,dy\,dz\left((dx)^2 + (dy)^2 \right)}^{I_{zz}} \dfrac{d\theta}{dt}

\end{array} \tag{14}

\]

The actual components which contribute to the moment are

\[

\label{dif:eq:tauTourqueD}

G_T+

\tau_{xy} - \tau_{xy} +

\overbrace{\dfrac{\partial \left( \tau_{yx} - \tau_{xy}\right)}{\partial y}}^{\cong 0}

= \rho \dfrac{\underbrace{\left((dx)^2 + (dy)^2 \right)}_{\scriptsize =0}}{12} \dfrac{d\theta}{dt} \tag{15}

\]

which means since that \(dx\longrightarrow 0\) and \(dy \longrightarrow 0\) that

\[

\label{dif:eq:tauTourqueF}

G_T+

\tau_{xy} = \tau_{yx} \tag{16}

\]

This analysis can be done on the other two directions and hence the general conclusion is that

\[

\label{dif:eq:tauij}

G_T+ \tau_{ij} = \tau_{ji} \tag{17}

\]

where \(i\) is one of \(x,y,z\) and the \(j\) is any of the other \(x,y, z\). For the case of \(G_T= 0\) the stress tensor becomes symmetrical. The gravity is a body force that is considered in many kind of calculations and this force cause a change in symmetry of the stress tensor. However, this change, for almost all practical purposes, can be neglected. The magnetic body forces on the other hand are significant and have to be included in the calculations. If the body forces effect is neglected or do not exist in the problem then regardless the coordinate system orientation

\[

\label{dif:eq:tauSymmetry}

\tau_{ij} = \tau_{ji} \qquad (i \neq j) \tag{18}

\]

### Contributors

Dr. Genick Bar-Meir. Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.2 or later or Potto license.