5.4: Zero-Force Members

Last updated
Save as PDF

Page ID: 91473

$ \newcommand{\vecs}[1]{\overset { \scriptstyle \rightharpoonup} {\mathbf{#1}} } $ $ \newcommand{\vecd}[1]{\overset{-\!-\!\rightharpoonup}{\vphantom{a}\smash {#1}}} $$\newcommand{\id}{\mathrm{id}}$ $ \newcommand{\Span}{\mathrm{span}}$ $ \newcommand{\kernel}{\mathrm{null}\,}$ $ \newcommand{\range}{\mathrm{range}\,}$ $ \newcommand{\RealPart}{\mathrm{Re}}$ $ \newcommand{\ImaginaryPart}{\mathrm{Im}}$ $ \newcommand{\Argument}{\mathrm{Arg}}$ $ \newcommand{\norm}[1]{\| #1 \|}$ $ \newcommand{\inner}[2]{\langle #1, #2 \rangle}$ $ \newcommand{\Span}{\mathrm{span}}$ $\newcommand{\id}{\mathrm{id}}$ $ \newcommand{\Span}{\mathrm{span}}$ $ \newcommand{\kernel}{\mathrm{null}\,}$ $ \newcommand{\range}{\mathrm{range}\,}$ $ \newcommand{\RealPart}{\mathrm{Re}}$ $ \newcommand{\ImaginaryPart}{\mathrm{Im}}$ $ \newcommand{\Argument}{\mathrm{Arg}}$ $ \newcommand{\norm}[1]{\| #1 \|}$ $ \newcommand{\inner}[2]{\langle #1, #2 \rangle}$ $ \newcommand{\Span}{\mathrm{span}}$$\newcommand{\AA}{\unicode[.8,0]{x212B}}$

This is a special case that is specially useful for method of joints and method of sections. These special types of members called zero-force members ensure the truss stays in a particular shape as a rigid body, but carries no load.

Zero-force members are members that you can tell just by inspection that they carry no load. They are important to the structure to ensure it stays in a rigid shape.

Zero-force members can be found considering the equilibrium equations. Look at joint e below. In the y direction, there is only 1 force: F_eh. So if the sum of the forces in the y direction $latex \sum F_{eh} = F_eh = 0, then F_eh = 0. Similarly, F_mkand F_cp are zero-force members (if you look at joint m and c). Note that if you looked at joint k or p, you couldn’t tell that F_mkand F_cp are zero-force members.

Adapted from original source: https://demo.webwork.rochester.edu/w...b27426a1d4.png

There isn’t a huge problem if you can’t find zero-force members just from inspection, but you might find that certain joints are not able to be solved as easily. (Zero-force members let you have one less unknown).

Also see that L and G have no zero-force members because the externally applied loads balance the members.

Here are some examples to practice on:

Example 1

Source: https://commons.wikimedia.org/wiki/F...back-truss.svg

(I count 3 zero-force members, assuming there are no loads on the bridge at the joints).

Example 2

Source: https://commons.wikimedia.org/wiki/F...ring-truss.svg

(I count 1 zero-force member, assuming there are no loads on the bridge at the joints).

Example 3

railway_railway_bridge_high_bridge_canal_bridge_hochdonn_canal_bridge-995729.jpgd_-1024x651.jpg

Source: https://pxhere.com/en/photo/995729

(Looking at only 1 side of the bridge, in theory there are 7 zero-force members, but because there is a load on the deck it is more likely that all of them would be carrying a load).

Admittedly, zero-force members are more theoretical than actual.

Key Takeaways

Basically: Zero-force members are two-force members that do not carry any load but help keep the structure into a certain shape.

Application: In trusses.

Looking ahead: We will talk about this again in sections 1.3 on vectors and in section 1.4 and 1.5 on dot products and cross products.